US Cabinet Handle Projection & Fixings Guide | Capramont & Co
Use this US guide to check cabinet pull projection, grip clearance, center-to-center spacing, fixing access and door thickness before a cabinet shop drills fronts. Capramont & Co supports US designers, builders and millwork teams with product pages, US Letter spec sheets, project review and Hardware Schedule support.
US field coordination
Confirm pull projection, grip space and screw access before a cabinet shop drills the fronts.
Use this section after the Shopify page intro to turn product selection into a US-ready check: center-to-center spacing, hole layout, projection, grip clearance, door thickness, rear access and the spec sheet route for submittals.
US jobsite risk points
The clearance issue is usually found too late.
Center-to-center
Hole spacing must match the selected pull, not only the elevation.
Projection
Check how far the hardware sits proud of the cabinet face.
Grip clearance
Confirm usable finger space behind, under or inside the pull.
Rear access
Door thickness and screw access affect whether the fixing is suitable.
Who uses this check
For US designers, builders, cabinet shops and millwork teams.
Interior designers
Use projection and grip-clearance notes to confirm that a pull looks right, feels right and can be signed off before a client approves finishes or a whole-home hardware schedule.
Cabinet shops
Use center-to-center and fixing information before drilling face-frame, inset or full-overlay doors, drawer fronts, appliance panels and refrigerator panels.
Architects and builders
Use US Letter spec sheets, product pages and project review where hardware has to be coordinated for submittals, drawings, finish approval or a multi-room schedule.
Measurement sequence
Check the hardware in the same order a US installer will fit it.
| Field check | What it means | Where it matters most | Capramont route |
|---|---|---|---|
| Center-to-center spacing | The distance between fixing points. It controls the drilling template and replacement hole compatibility. | Drawer banks, existing holes, repeated elevations and long cabinet pulls. | Review center-to-center guidance. |
| Projection from cabinet face | The distance the knob, pull, cup pull, C pull or T-bar stands proud from the door or drawer front. | Inset cabinetry, adjacent panels, traffic areas, narrow aisles and appliance banks. | Check the PDP and US Letter spec sheet where available. |
| Grip clearance | The usable space for fingers behind, under or inside the hardware. | Low-profile pulls, C pulls, cup pulls, closet cabinetry and high-use drawers. | Order a finish sign-off sample or request product review. |
| Door thickness and screw length | The front thickness and rear access determine whether supplied fixings and screw length are suitable. | Custom cabinetry, custom millwork, thick drawer fronts and appliance panels. | Send drawings or door details. |
| Submittal documentation | A US Letter spec sheet or product page should support the selection before ordering. | Trade projects, builder review, interior design sign-off and multi-room schedules. | Build a spec pack. |
US cabinet construction
Projection can behave differently by cabinet build type.
Frame and overlay conditions
- Face-frame cabinetry: confirm rail, stile and edge clearances.
- Inset cabinetry: check projection and adjacent-door swing before drilling.
- Full-overlay cabinetry: check repeated alignment and finger clearance across banks.
- Slab drawer fronts: confirm handle scale, centerline and pull comfort.
Room and panel conditions
- Appliance panels and refrigerator panels need stronger scale and fixing review.
- Closet cabinetry may need long pulls with comfortable grip clearance.
- Laundry room and mudroom cabinetry should be checked for high-use handling.
- Bathroom vanities need finish and clearance checks before sign-off.
For US projects, keep center-to-center spacing, projection, door thickness, orientation and finish approval in one record. A Hardware Schedule helps prevent conflicting notes between the designer, builder, cabinet shop and installer.
Product examples for US clearance checks
Use product pages and US Letter spec sheets before drilling.
These examples show common hardware formats that need different clearance and fixing checks. Product dimensions and US Letter spec sheets should be checked on the product page before release to the cabinet shop.
Westbourne Cabinet Pull
Beaufort C Pull
Westbourne C Pull
Farringdon Cup
Maddox Cabinet Handle
Submittal and schedule control
Keep the clearance decision out of email threads.
| Document or route | Use it for | Inputs to confirm | Best next action |
|---|---|---|---|
| US Letter spec sheet | Product-level submittal support before a cabinet shop drills fronts. | Product name, finish, centers, projection and fixing notes. | Open the product card link or build a spec pack. |
| Project & Drawing Review | Appliance panels, refrigerator panels, unusual front thickness and repeated elevations. | Door count, elevations, orientation, existing holes and cabinet construction. | Send drawings or details. |
| Hardware Schedule | Whole-home cabinetry, multi-room orders and revision control. | Room, quantity, product, size, finish, centers, orientation and approval status. | Start a Hardware Schedule. |
| Custom center review | Existing holes, non-standard spacing or custom millwork requirements. | Hole spacing, drawer width, rail/stile limits and final front thickness. | Review custom centers. |
Before release to production
Send details when the hardware affects drilling, clearance or repeated alignment.
Send product choices, cabinet construction, door thickness, existing hole measurements, elevations or photographs when the project includes appliance panels, refrigerator panels, inset cabinetry, face-frame cabinetry, closet cabinetry, laundry rooms, mudrooms, thick fronts or repeated drawer banks.
Specification links for US projects
Move from clearance check to selection, sign-off and ordering route.
US Specification Center
Start with samples, finish approval, project review and schedule support.
Pull Size & Placement
Check scale, placement and hand space across doors, drawers and panels.
Center-to-Center Guide
Match hole spacing, replacement pulls and drilling templates.
Installation / Fitting Guide
Coordinate drilling sequence, fixings and installer handoff.
Short answers
US projection, clearance and fixing questions
What is projection on a cabinet pull?
Projection is how far the pull, knob or cup pull stands out from the cabinet face. It affects grip comfort, clearance beside other doors, appliance-panel use and whether the hardware feels balanced on the selected front.
Is grip clearance the same as projection?
No. Projection is the outward depth of the hardware, while grip clearance is the usable finger space behind, under or inside it. A pull can have enough projection but still feel tight if the hand path is shallow.
When should a US project use drawing review?
Use drawing review when the hardware is going on appliance panels, refrigerator panels, inset cabinetry, face-frame fronts, thick custom fronts, existing holes or repeated drawer banks. A quick review can prevent drilling errors before made-to-order production.
Should a cabinet shop use the product page or the spec sheet?
Use both where available. The product page supports product selection and imagery; the US Letter spec sheet supports submittals, dimensions, centers, projection and fixing checks before drilling or release to production.