Small upper doors
Use a compact pull or T-bar where the door is light and the hardware should stay visually quiet.
Upper cabinets
Secondary rooms
US Flat-Front Kitchen Cabinet Pulls Guide | Capramont & Co
For US flat-front kitchens, cabinet pulls need to be sized by cabinet construction, drawer width, appliance panels and center-to-center drilling. Capramont & Co supports British-made cabinet hardware specification with finish samples, US Letter spec sheets, custom center review, project review and hardware schedule support before made-to-order production.
US cabinet planning
Start with cabinet construction before choosing a pull
Flat-front kitchens in US projects can include face-frame boxes, full-overlay fronts, inset cabinetry, slab drawers, appliance panels and refrigerator panels. Each condition changes the safest pull length, center-to-center drilling, projection and grip clearance.
Construction check
Check the cabinet face before the drilling plan is issued
A clean flat front gives the hardware more visual authority. Use the cabinet construction, room use and opening weight to decide whether the project needs a compact pull, a longer bar, a C pull or a project-reviewed appliance pull.
| US cabinet condition | Hardware decision | What to check before drilling | Best route |
|---|---|---|---|
| Full-overlay slab drawers | Linear cabinet pull | Keep the same datum line across drawer fronts so the run reads as one controlled elevation. | Review Beaufort |
| Face-frame cabinetry | Pull or restrained T-bar | Confirm rail and stile positions so the pull does not crowd the frame or sit too close to the edge. | View Hardware Finder |
| Inset cabinetry | Pull with projection review | Check reveal, hand clearance and projection because flat fronts and inset gaps make small errors visible. | Check projection guide |
| Appliance or refrigerator panel | Long pull after project review | Review fixing strength, leverage, panel thickness and usable grip before the cabinet shop drills. | Plan appliance pulls |
| Closet, laundry room or mudroom cabinetry | Durable pull with repeatable placement | Use a practical size for daily use and keep center-to-center logic consistent across secondary rooms. | Start a Hardware Schedule |
Center-to-center planning
Match pull length to drawer width, door height and hole spacing
For US submittals, write the pull size in inches first with millimeters shown for the Capramont specification. Check center-to-center drilling separately from overall length, because the cabinet shop drills to the centers, not to the outside length.
Drawer stacks
Use a repeated horizontal pull size and keep the datum line consistent across the whole drawer bank.
3.6–14.3 in / 92–364 mm centers
Tall doors and panels
Use longer pulls when the front is tall, heavy or visually dominant. Review appliance panels before release.
6.7–27.2 in / 170–690 mm overall
Drilling note: confirm center-to-center size, overall length, projection, grip clearance, fixing method, door thickness and handed placement before production. Use project review where appliance panels, refrigerator panels or unusual drawer widths are involved.
Hardware choice
Choose by grip, clearance and visual weight
| Hardware type | Where it works | US specification note | Internal route |
|---|---|---|---|
| Linear cabinet pulls | Slab drawers, full-overlay doors, pantry runs and clean kitchen elevations. | Best where the project needs repeatable center-to-center drilling and a controlled horizontal read. | View Hardware Finder |
| Long pulls | Tall pantry fronts, closet doors, appliance panels and refrigerator panels. | Review fixing strength and projection before drilling heavy or frequently used panels. | Send Project Details |
| C pulls | Minimal fronts where a quieter grip is preferred. | Use when the design should avoid a projected bar but still needs a defined pull point. | Review Beaufort C Pull |
| T-bars | Smaller upper doors, bar cabinetry and secondary room fronts. | Use selectively so the flat-front elevation does not become too busy. | Compare options |
US product shortlist
Shortlist Capramont pulls for slab and panel-front work
These Capramont product routes use verified PDP handles, images and US Letter spec sheet URLs from the product export. Use the PDP first for finish options, imagery and current product detail.
Beaufort Cabinet Handle
Use where a restrained contemporary pull needs repeatable center-to-center drilling across drawer banks. Centers: 3.6–14.3 in / 92–364 mm.
Westbourne Cabinet Pull
Use where the flat-front elevation needs a crisp linear pull with a slightly stronger design line. Centers: 3.6–14.3 in / 92–364 mm.
Maddox Cabinet Handle
Use for taller doors, appliance-style fronts and refrigerator panel planning after project review. Overall length range: 6.7–27.2 in / 170–690 mm.
Melbury Cabinet Handle
Use where the same pull family needs to carry from the kitchen into pantry, closet, laundry room or mudroom cabinetry. Overall length range: 6.7–27.2 in / 170–690 mm.
Pembridge Cabinet Handle
Use where a more architectural pull is needed across tall fronts, drawer stacks or modern custom millwork. Overall length range: 6.7–27.2 in / 170–690 mm.
Beaufort C Pull
Use when the design calls for a quieter grip on smaller fronts or secondary cabinetry. Centers: 1.3–2.3 in / 32–58 mm.
Finish approval
Approve the finish against the actual cabinet color and lighting
Flat-front kitchens leave fewer visual breaks, so the finish should be checked physically before the order is released. Review the sample against painted fronts, veneers, stone, appliance finishes and room lighting.
Warm brass schemes
Check against white oak, walnut, off-white paint, cream stone and warmer appliance palettes.
Bronze schemes
Use where the hardware should sit quieter than brass but warmer than black hardware.
Black schemes
Use where the designer wants a deliberate graphic line on light, oak or dark slab fronts.
Nickel and stainless schemes
Use where the kitchen has cooler cabinetry, stainless appliances or a more architectural palette.
Submittal workflow
Use US Letter spec sheets before the cabinet shop drills
A flat-front hardware schedule should capture room, cabinet location, product name, finish, quantity, center-to-center size, overall length, projection notes and approval status. Use the US Letter spec sheets in the product cards above for project files and submittals.
| Project stage | What to confirm | Why it matters on flat fronts | Next action |
|---|---|---|---|
| Design shortlist | Pull family, finish direction and cabinet construction. | The hardware is one of the few visible details on a slab or panel-front elevation. | View Hardware Finder |
| Submittal pack | US Letter spec sheet, PDP link, finish sample route and size notes. | The cabinet shop needs one source of truth before drilling centers are released. | US Specification Center |
| Appliance panel review | Panel thickness, pull position, fixing strength, projection and grip clearance. | Refrigerator and appliance panels create more leverage than standard drawer fronts. | Send Project Details |
| Whole-home release | Rooms, quantities, finishes, sizes, centers and approval status. | Closets, laundry rooms and mudrooms need the same controlled logic as the kitchen. | Start a Hardware Schedule |
Project review
Review custom centers before the drilling decision is locked
Use project review when the kitchen includes appliance panels, refrigerator panels, tall doors, non-standard hole spacing, inset cabinetry, a whole-home package or a cabinet shop submittal that needs sign-off before ordering.
US FAQ
Flat-front kitchen pull FAQs for US projects
What cabinet pulls work best on flat-front kitchen cabinets?
Linear pulls, longer bar pulls and low-profile C pulls usually work best on flat-front kitchens because they give the cabinet face a controlled grip point without adding extra ornament. The right choice depends on drawer width, cabinet construction and projection.
Should I specify inches or millimeters for Capramont pulls?
Use inches first for US project notes, then include millimeters for the Capramont specification. Center-to-center drilling should be written clearly because the cabinet shop drills to the centers, while the overall length controls the visual scale.
Do refrigerator panels need a different pull review?
Yes. Refrigerator panels and appliance panels should be reviewed separately because they add leverage, weight and clearance questions. Confirm the panel thickness, fixing location, projection and grip comfort before releasing the drilling plan.
Can the same pull family run through closets, laundry rooms and mudrooms?
Yes, provided the sizes and placements are adapted to each room. A consistent pull family can work across kitchen, pantry, closet, laundry room and mudroom cabinetry when the hardware schedule controls quantity, finish, centers and placement.
Next step
Send the project before flat-front drilling is fixed
For US flat-front kitchen projects, send drawings or project details when pull sizing, appliance panels, custom centers, finish approval or a multi-room hardware schedule needs review before made-to-order production.