Westbourne Cabinet Pull
92–364 mm centresCabinet pull
Useful where existing two-hole pull centres match the Capramont standard handle ladder.
Replace Cabinet Handles Without Redrilling Guide | Capramont & Co
To replace cabinet handles without redrilling, measure the centre-to-centre distance between the existing fixing holes, then choose a handle with matching centres or request a custom-centre review. Capramont & Co helps specifiers select British-made cabinet hardware using centre checks, samples, finish sign-off, PDP proof and project/drawing review before ordering.
Existing holes first
Do not choose by overall length first
The no-redrill route starts with the fixing holes already in the cabinet front. Overall length affects appearance and coverage, but centre-to-centre size determines whether the new handle can physically fit without drilling new holes.
Measure correctly
Measure centre-to-centre
Remove one existing handle and measure from the centre of one fixing hole to the centre of the other. Do not measure the visible length of the old handle and assume it will match.
Rule: if the new handle matches the existing centre-to-centre measurement, it can usually be fitted using the existing holes. If it does not match, use the custom-centre or project review route.
Replacement workflow
Six checks before choosing replacement hardware
1
Remove one handle
Use the exposed cabinet holes as the source of truth. Old handle length can be misleading.
2
Measure the centres
Measure in millimetres from the centre of one fixing hole to the centre of the other.
3
Check overall length
Overall length helps assess proportion and whether old marks or finish shadows may remain visible.
4
Match product data
Use PDP specification tables and A4 tear sheets to confirm centres, projection and finish route.
5
Review unusual holes
If the centres are non-standard, send photos and measurements before redrilling or ordering.
6
Sign off finish
Use a sample or finish sign-off route before made-to-order production, especially for project work.
Decision table
Which route should you use?
| Existing condition | Best route | Why it matters | Next step |
|---|---|---|---|
| Existing holes match a Capramont centre size | Choose the matching PDP size | Preserves the cabinet front and avoids unnecessary redrilling. | View Hardware Finder |
| Existing centres are unusual or not exact | Review custom centres | Small centre errors can create visible misalignment or fixing problems. | Review Custom Centres |
| Old handle left marks or finish shadows | Check overall length and style coverage | The new handle may fit the holes but fail visually if old marks remain visible. | Send Project / Drawing Details |
| Replacing cup pulls | Match cup pull fixing centres | Cup width and fixing centres are different measurements. | See product proof |
| Whole kitchen or multi-room replacement | Start a Hardware Schedule | Keeps products, centres, finishes, quantities and approvals controlled. | Start a Hardware Schedule |
Product proof
Replacement-friendly product routes
These product routes use visible centre-to-centre data and A4 specification sheets. Check the live PDP before ordering and use project review where existing holes, marks or quantities are uncertain.
Beaufort Cabinet Handle
92–364 mm centresCabinet handle
A clean replacement route for projects that need visible centre data and a controlled specification sheet.
Burlington Cabinet Handle
92–604 mm centresLong pull route
Useful where replacement work includes larger drawers, tall units or longer handle proportions.
Farringdon Handle
92–604 mm centresCabinet handle
A flexible handle route where replacement work needs a broad centre-size range.
Brunswick Cabinet Handle
158–675 mm centresAlternative centre ladder
Useful when the existing holes are closer to the longer Brunswick centre ladder rather than the standard 92–604 mm ladder.
Maddox Cabinet Handle
84–562 mm centresAlternative centre ladder
Useful for projects where existing centres do not match the main 92 mm starting point.
C pulls and cup pulls
Check fixing centres by hardware type
Cup pull width, C pull length and cabinet handle length are not the same as fixing centres. Match the fixing centres first, then assess overall size, projection and visual coverage.
| Product route | Hardware type | Centres to check | Specification proof |
|---|---|---|---|
| Westbourne C Pull | C pull | 32, 46, 58 mm | A4 spec sheet |
| Beaufort C Pull | C pull | 32, 46, 58 mm | A4 spec sheet |
| Farringdon Cup | Cup pull | 50, 86, 138 mm | A4 spec sheet |
| Egerton Cup | Cup pull | 50, 86, 138 mm | A4 spec sheet |
| Eccleston Cup | Cup pull | 50, 86, 138 mm | A4 spec sheet |
When not to redrill
Use custom-centre review for awkward existing holes
Do not redrill immediately if the cabinet front is painted, veneered, installed, marked by previous hardware or part of a multi-room project. A custom-centre route may preserve the front and reduce fitting risk.
Send for review
What to send
For a single room: centre-to-centre measurement, old handle length, photos, quantity, finish preference and product interest.
For a project: room list, door/drawer counts, elevations, existing schedule, finish direction and approval contact.
Finish and project control
Check finish, scale and approval before production
Replacement hardware has to work with existing cabinetry, old fixing marks, paint colours, timber tones and the project approval route. Use samples or finish sign-off before made-to-order production.
Hardware Schedule
Use for whole-kitchen, whole-home or multi-room replacement projects.
Start a ScheduleTrade Access
Use after project or supplier fit is established. SparkLayer is for approved trade ordering.
Apply for Trade AccessInternal specification links
Related specification guides
Specification CentreMain hub for samples, finish sign-off, project review and Hardware Schedule support.
Common Centres / Replacement MatrixUse this when you already know the existing fixing centres and need a size route.
Custom Centres GuideUse this when existing holes do not match a standard product centre.
Handle Size & Placement GuideUse for new cabinetry, new hole placement and drawer/door proportion decisions.
Finish & Cabinet Colour MatchingUse for finish direction against painted fronts, timber, stone and metalwork.
Materials and FinishesReview finish families, material routes and sign-off considerations.
Hardware FinderBrowse handles, knobs, C pulls, cup pulls and product routes.
Made in EnglandManufacturing and provenance context for British-made cabinet hardware.
Lead Times & SchedulingCheck made-to-order production timing and project scheduling notes.
Visible FAQs
Replacement hardware FAQs
Can I replace cabinet handles without drilling new holes?
Yes, if the new handle has the same centre-to-centre fixing measurement as the existing holes. Measure the cabinet holes first, then choose a product size with matching centres.
What does centre-to-centre mean?
Centre-to-centre means the distance from the centre of one fixing hole to the centre of the other. It is the key measurement for two-point replacement handles.
Should I measure the old handle or the cabinet holes?
Measure the cabinet holes where possible. The old handle can be misleading if it is bent, worn, loose or not accurately aligned.
What if my existing holes do not match a standard size?
Send the measurement, photos or drawings for review. A custom-centre route may be better than redrilling, especially on high-value cabinetry.
Can cup pulls be replaced using existing holes?
Yes, but cup pulls have their own fixing centres. Do not match by width alone. Check fixing centres and drawer rail clearance.
Should I order a sample first?
Yes. Samples and finish sign-off reduce finish and scale risk before made-to-order production, especially for project-led replacement work.
Final check
Need existing holes checked before ordering?
Send the centre measurement, photos, quantity and product interest. Capramont & Co can review whether the replacement route should use a standard PDP size, custom centres or a controlled Hardware Schedule.
US hole spacing first
Match center-to-center before you choose the pull
For US replacement projects, the existing cabinet holes control the route. Measure the hole spacing from screw center to screw center, then choose a cabinet pull with matching centers before you judge style, overall length, finish or room fit.
Definition
Center-to-center means screw hole to screw hole
Center-to-center is the distance between the center of one fixing hole and the center of the second fixing hole. This is different from overall pull length. A longer pull may look right but still fail if the screw centers do not match.
No-redrill rule: if the new pull matches the existing center-to-center hole spacing, the cabinet front can usually be reused. If it does not match, use the custom center or project review route before drilling.
Replacement or new layout?
Decide whether the holes stay or move
| US project condition | What to check first | Best route | Next step |
|---|---|---|---|
| Existing drawer fronts with two visible holes | Center-to-center hole spacing and old pull coverage. | Match a pull with identical centers. | Check the center guide |
| New custom cabinetry or custom millwork | Drawer width, door rail/stile width, appliance panel scale and planned pull length. | Use the placement and size route before drilling. | Open the placement guide |
| Old holes are close but not exact | Whether a custom center can use the existing cabinet front cleanly. | Review custom centers before redrilling. | Review custom centers |
| Whole-home, closet, laundry room or mudroom package | Room list, quantities, finish direction and approval route. | Use a hardware schedule to control changes. | Start a hardware schedule |
US cabinetry checks
Check the cabinet construction before ordering
1
Face-frame cabinetry
Confirm the pull does not interfere with rails, stiles, adjacent doors or drawer stack spacing.
2
Inset cabinetry
Check projection and grip clearance so the pull works with tight reveal lines and neighboring fronts.
3
Full-overlay fronts
Make sure replacement pulls sit consistently across door pairs, drawers and tall panels.
4
Appliance panels
Refrigerator panels and integrated appliances usually need longer pull proportions and stronger schedule control.
5
High-use rooms
Laundry rooms, mudrooms and pantries need grip clearance, finish approval and practical projection checks.
6
Closet cabinetry
Long runs of closet doors need consistent centers, finish samples and a controlled room-by-room count.
Pull size and clearance
Use inches first, then confirm the metric centers
Capramont product pages and US Letter spec sheets give the technical product route. Use inch guidance for quick planning, then confirm the exact metric center-to-center value before ordering or sending a submittal.
| Cabinet area | Useful replacement check | Common Capramont center route | Risk to avoid |
|---|---|---|---|
| Standard drawers and doors | Match the existing hole spacing first. | 3.6–14.3 in / 92–364 mm centers | Choosing by overall pull length instead of centers. |
| Wide drawers and tall cabinet doors | Check proportion, projection and finger clearance. | 3.6–23.8 in / 92–604 mm centers | A pull that fits the holes but looks too small for the front. |
| Appliance and refrigerator panels | Confirm panel thickness, fixing route and pull scale. | Long pull or appliance-panel route | Using a standard drawer pull on a heavy appliance panel. |
| Cup pulls and C pulls | Check fixing centers, not just cup width or visible length. | Cup pull centers and C pull centers vary by product | Matching by width while the screw holes do not line up. |
Measurement workflow
How to measure an existing cabinet pull
1
Remove one pull
Expose the actual screw holes. Do not rely on the old pull's visible length.
2
Measure screw centers
Measure from the center of one hole to the center of the other. Record the number in inches and millimeters if possible.
3
Photograph the front
Take a straight-on photo showing holes, old marks, stile/rail width and drawer or door size.
4
Check old shadow marks
The new pull may fit the holes but still fail visually if the previous hardware left a mark.
5
Compare the product page
Use the PDP and US Letter spec sheet for centers, projection, overall length and fixing notes.
6
Send uncertain projects
For multiple rooms, custom millwork or unusual spacing, send the project before ordering or drilling.
Product proof
US product routes for no-redrill replacement
These routes use real Capramont product pages and verified US Letter spec sheets where available. Confirm the live PDP before ordering and use project review for unusual holes, finish shadows or multi-room schedules.
Westbourne Cabinet Pull
3.6–14.3 in / 92–364 mm centersCabinet pull
A strong route for two-hole replacements when the existing drawer or door holes match the main Capramont center ladder.
Beaufort Cabinet Handle
3.6–14.3 in / 92–364 mm centersCabinet handle
Useful for kitchen, pantry, laundry room and mudroom cabinetry where proportion and grip clearance need to stay controlled.
Burlington Cabinet Handle
3.6–23.8 in / 92–604 mm centersLong pull route
A practical option when replacement work includes wide drawers, tall cabinet doors, appliance panels or refrigerator panel proportions.
Farringdon Handle
3.6–23.8 in / 92–604 mm centersCabinet handle
Use where the project needs a broad range of center sizes across doors, drawers, closet cabinetry and taller panels.
Brunswick Cabinet Handle
6.2–26.6 in / 158–675 mm centersAlternative center ladder
Useful when the existing hole spacing is closer to the Brunswick center ladder than the standard 92–604 mm route.
Maddox Cabinet Handle
Alternative centersVerify PDP before ordering
Use when the existing hole spacing does not fit the main center ladder and the project needs a controlled product-page review.
Cup pulls and C pulls
Do not match cup pulls by width alone
Cup pull width, C pull length and cabinet pull overall length are not the same as hole spacing. Use the product page and US Letter spec sheet to confirm the fixing centers before you remove or redrill hardware.
| Product route | Hardware type | What to confirm | US documentation |
|---|---|---|---|
| Westbourne C Pull | C pull | Hole spacing, edge clearance and cabinet-front thickness. | US Letter spec sheet |
| Beaufort C Pull | C pull | Hole spacing and grip clearance on doors and drawers. | US Letter spec sheet |
| Farringdon Cup | Cup pull | 2.0 in / 50 mm, 3.4 in / 86 mm or 5.4 in / 138 mm center route. | US Letter spec sheet |
| Egerton Cup | Cup pull | 2.0 in / 50 mm, 3.4 in / 86 mm or 5.4 in / 138 mm center route. | US Letter spec sheet |
| Eccleston Cup | Cup pull | 2.0 in / 50 mm, 3.4 in / 86 mm or 5.4 in / 138 mm center route. | US Letter spec sheet |
Custom centers
Use custom center review before redrilling valuable fronts
If the existing holes are unusual, slightly off standard, or on finished painted, veneered or inset fronts, a custom center route may reduce damage risk and preserve the cabinet front.
Submittal-ready inputs
What US teams should send
For a single room: center-to-center measurement, photos, quantity, product interest, finish direction and old hardware marks.
For a project package: room list, door/drawer counts, appliance panel notes, elevations, hardware schedule draft and approval contact.
Finish approval
Approve finish and scale before made-to-order production
Replacement pulls need to work with existing paint, stain, stone, appliances and old fixing marks. Use a finish sample and product documentation before ordering, especially for whole-home or trade-led work.
Finish sample
Use a physical finish route before production when cabinetry, lighting or appliance finishes need approval.
Order Finish Sign-OffUS spec pack
Use product pages and US Letter spec sheets for submittals, project folders and client approval.
Build a Spec PackTrade route
Use trade access after the project or repeat cabinet shop relationship has been reviewed.
Apply for Trade AccessUS Specification Center links
Continue the US replacement route
US Specification CenterMain route for samples, finish approval, project review and hardware schedule support.
Center-to-Center GuideUse this when you already know the existing hole spacing and need a replacement route.
Custom Center Cabinet PullsUse this when existing holes do not match a standard product center.
Cabinet Pull Placement GuideUse for new cabinetry, drawer placement and door-front proportion decisions.
Projection and FixingsCheck finger clearance, fixing details and installation risk before ordering.
Installation and FittingSupport installers with drill checks, fitting sequence and cabinet-front handling.
Short FAQs
US replacement pull questions
Can I replace cabinet pulls without drilling new holes?
Yes, if the new cabinet pull has the same center-to-center hole spacing as the existing holes. Measure the holes first, then match a product size before choosing finish or overall length.
Should I measure in inches or millimeters?
Use both if possible. Inches are useful for US planning, but the product centers must be confirmed exactly because most premium cabinet hardware uses precise metric center-to-center values.
What if my existing holes are not a standard size?
Send photos, measurements and product interest for custom center review before redrilling. This is especially important for painted, veneered, inset or finished custom cabinetry.
Are cup pulls measured the same way as cabinet pulls?
No. Cup pull width and screw centers are different checks. Confirm the fixing centers on the product page or US Letter spec sheet before assuming a cup pull will reuse existing holes.
Project review
Need the existing holes checked before ordering?
Send hole spacing, photos, quantities, room use and product interest. Capramont & Co can help determine whether the US replacement route should use a standard product size, custom centers or a controlled hardware schedule.